mandy_xintai@cnxtyy.com    0086 577 26886398
Cont

Har du noen spørsmål?

0086 577 26886398

May 02, 2022

Hvilke plastprodukter er polypropylen HP550J egnet for?

Engelsk navn: Polypropylene

Forkortelse: PP,

En termoplastisk harpiks oppnådd ved polymerisasjon av propylen. Det er tre konfigurasjoner av isotaktisk, tilfeldig og syndiotaktisk, og industrielle produkter er hovedsakelig sammensatt av isotaktiske. Polypropylen inkluderer også kopolymerer av propylen med små mengder etylen. Vanligvis gjennomskinnelig fargeløst fast stoff, luktfritt og ikke-giftig. På grunn av den vanlige strukturen og høye krystalliseringen er smeltepunktet så høyt som 167 grader C, varmebestandighet, og produktene kan steriliseres med damp, som er dens enestående fordeler. Med en tetthet på 0.90g/cm3 er det den letteste plasten for generell-bruk. Korrosjonsmotstand, strekkfasthet 30MPa, styrke, stivhet og gjennomsiktighet er bedre enn polyetylen. Ulempen er at den har dårlig slagfasthet ved lav temperatur og er lett å eldes, men den kan overvinnes ved modifikasjon og tilsetning av antioksidanter.

Funksjoner:

Ikke-giftig, luktfri, lav tetthet, styrke, stivhet, hardhet og varmebestandighet er bedre enn lavtrykkspolyetylen, kan brukes ved ca. 100 grader. Den har gode elektriske egenskaper og høyfrekvent isolasjon som ikke påvirkes av fuktighet, men blir sprø ved lav temperatur, Ikke slitasjebestandig-, lett å eldes. Egnet for å lage generelle mekaniske deler, korrosjonsbestandige-deler og isolerende deler. Vanlige syre- og alkaliorganiske løsemidler har liten effekt på det og kan brukes til servise.

produksjonsmetode:

①Slurry method. Polymerization in a diluent such as hexane is the earliest industrialized and by far the most productive method. ② liquid phase bulk method. Polymerization was carried out in liquid propylene at 70 degree and 3MPa. ③ gas phase method. The polymerization is carried out under the condition that the propylene is in the gaseous state. The latter two methods do not use diluent, the process is short, and the energy consumption is low. Liquid bulk methods have now shown the advantage of coming later.

Støpeegenskaper:

1. Krystallinsk materiale, lav hygroskopisitet, lett å smelte og sprekke, og lett å dekomponere etter lang-kontakt med varmt metall.

2. Fluiditeten er god, men krympeområdet og krympingsverdien er store, og krympehull, bulker og deformasjoner er tilbøyelige til å oppstå.

3. Kjølehastigheten er rask, hellesystemet og kjølesystemet bør spre varmen sakte, og vær oppmerksom på å kontrollere støpetemperaturen. Det er lett å orientere seg når materialtemperaturen er lav og høyt trykk. Når formtemperaturen er lavere enn 50 grader, er ikke plastdelene glatte, og det er lett å produsere dårlige sveise- og flytemerker. Det er lett å skje deformasjoner over 90 grader

4. Tykkelsen på plastveggen må være jevn for å unngå mangel på lim og skarpe hjørner for å hindre spenningskonsentrasjon.

bruk

Biaksialt orientert polypropylenfilm

Packaging materials occupy an extremely important position in plastic products. According to statistics, the world's plastics used in packaging account for about 35 percent of the total plastic consumption. my country's packaging plastics have developed rapidly, and the output has rapidly increased from 190,000 tons in 1980 to 4.65 million tons in 2003. It is expected to exceed 5.5 million tons in 2005, 7 million tons in 2010, and 9 million tons in 2015, accounting for about 5.5 million tons in 2010. More than 13 percent of the country's total packaging output.

From the product point of view, packaging films account for more than 50 percent of the total packaging plastics. my country's biaxially oriented polypropylene (BOPP) film is one of the areas with the largest consumption of PP resin. In 2003, there were 86 BOPP production enterprises (123 production lines) in my country, with a total production capacity of about 1.4 million t/a. In 2004, it reached 200. 10,000 t/a (138 production lines), and the output will exceed 1 million t. In recent years, domestic enterprises have paid attention to improving the competitiveness of their products, and have successively introduced a number of advanced BOPP production equipment, which can produce films with a width of up to 8.3m and a line speed of up to 400500m/min. For example, Zhejiang Dadongnan Group introduced German Bruckner 6 10,000 t/a production line; Guofeng Group invested 200 million yuan to introduce a 35,000 t/a production line (currently the first in Asia and the fourth in the world with 10m wide BOPP equipment); Changzhou Wujin Jinshi Group introduced 20,000 t/a in Germany Five-layer co-extrusion high-strength and ultra-thin BOPP production line; Fujian Hyundai Group introduced a 25,000 t/a production line; Baoshuo Group plans to introduce a 100,000 t/a production line. According to my country's existing BOPP film production capacity, the annual demand for PP resin is nearly 2 million t. Therefore, attention should be paid to the development of PP special materials with high line speed, elongation and transparency for BOPP films, including supporting PP materials. , propylene copolymer to adapt to the newly introduced BOPP film equipment.

Modifisert polypropylen for biler

In 2003, my country's automobile production was more than 4.4 million units, ranking fourth in the world, with a year-on-year increase of 36.6 percent . According to the US ESM WerWide report: "In 2008, China's automobile production will exceed 6 million vehicles, and in 2015, it will surpass Japan and become the second largest in the world".

The development of the automobile industry is inseparable from the process of automobile plasticization. At present, the self-sufficiency rate of engineering plastics in my country is less than 16 percent . According to the forecast of China Engineering Plastics Association, the demand growth rate of engineering plastics in my country in 2005 was 15 percent , and in 2010, it was about 10 percent , and the demand will increase from 440,000 tons in 2000 to 1.4 million tons in 2010. The demand for engineering plastics in my country's automobile manufacturing industry is growing rapidly, and the total consumption will reach 940,000 tons by 2010 (calculated by the amount of plastics accounting for 5 percent to 10 percent of the weight of the vehicle).

PP har sterk konkurranseevne i bilindustrien, men på grunn av sin lave modul og varmebestandighet, og dårlige slagstyrke, kan den ikke brukes direkte som bildeler. De modifiserte PP-produktene som brukes i biler er motstandsdyktige mot Den termiske ytelsen kan økes fra 80 grader til 145 grader 150 grader, og den tåler høy temperatur i 7501000 timer uten aldring og sprekkdannelse. Ifølge rapporter kan en ny generasjon polypropylen HEHCPP-produkter med høy orienteringskrystallinitet lansert av Toyota Corporation of Japan brukes som dashbord og støtfangere for biler, noe som kan redusere kostnadene med 30 prosent sammenlignet med lignende produkter produsert med TPO som råmateriale. Modifisert PP brukes til biler. Tilbehør har svært brede utviklingsmuligheter.

Polypropylen for husholdningsapparater

In recent years, my country's household appliance industry has developed rapidly, with many varieties and large output. In 2003, my country produced 18.5 million refrigerators, 42 million air conditioners, 17 million washing machines, and 35 million microwave ovens. According to the "2004-2006 China Urban Home Theater Market Research and Consultation Report", it is expected that my country's home theater system market will reach 6.9 million units in the next three years. In addition, various small household appliances also have a huge potential market, which is an excellent business opportunity for modified PP. At present, some plastic raw material manufacturers in my country have developed special materials for washing machines, such as PP 1947 series, K7726 series, etc., which are welcomed by washing machine manufacturers. Therefore, in the next few years, the development of PP special materials for household appliances should be increased to meet the changing needs of the market.

Polypropylen for rør.

I 2003 oversteg den nasjonale totale produksjonen av plastrør 1,8 millioner tonn, en år{3}}til-økning på 23 prosent. I de tidlige dagene ble PP-rør hovedsakelig brukt som vannrør til landbruket, men markedet klarte ikke å åpne seg på grunn av noen problemer med ytelsen til de tidlige produktene (slagstyrke og dårlig aldringsmotstand). Med introduksjonen av utenlandsk avansert teknologi av Shanghai Plastic Building Materials Factory, har rørene for transport av kaldt og varmt vann produsert av importerte PP-R-materialer blitt anerkjent av markedet. For tiden har mange produsenter bygget produksjonslinjer for PP-R-rør, og prisen økes også med. Prisen på 20,000-30 000 yuan/tonn i den innledende produksjonsfasen har fortsatte å falle, men markedsandelen til PP-R-rør i plastrørmarkedet er fortsatt svært lav. Ifølge rapporter er det fortsatt et visst gap mellom innenlandske PP-R-materialer og importerte materialer, og kvaliteten må forbedres og forbedres. Ifølge rapporter har Sør-Korea utviklet en ny kvalitet av tilfeldig kopolymer polypropylen PP-R 112 for høytrykksvannforsyningsrør. Rørene produsert av denne klassen kan brukes i 50 år under ultrahøytrykkstilstanden på 20 grader C og 11,2 MPa.

Plastic pipes are one of the key products for the promotion and application of chemical building materials in my country. The Ministry of Construction issued a "Notice on Strengthening the Production Management and Promotion and Application of Copolymerized Polypropylene (PP-R, PP-B) Pipes" in 2001, requiring relevant departments Work together to do a good job from raw materials, processing, quality to pipe use and installation, and strictly control the quality of PP pipes, so as to better do a good job in the production, application and promotion of PP pipes in my country.

Svært gjennomsiktig polypropylen

With the continuous improvement of people's living standards, it will inevitably bring about different requirements and improvements in various aspects such as culture, entertainment, food, medical care, materials, and room decoration. Many items in the market are increasingly using transparent materials. Therefore, the development of transparent PP special materials is a good development trend, especially the PP special materials with high transparency, good fluidity and fast forming are required in order to be designed and processed into popular PP products. Transparent PP is more characteristic than ordinary PP, PVC, PET, PS, and has more advantages and development prospects.

In recent years, the foreign transparent PP market has grown rapidly. For example, South Korea's LG introduced transparent PP to the market as a substitute for PET; some German companies replaced PVC with transparent PP; the growth rate of transparent PP products in the United States was 7 percent higher than that of ordinary PP products. 9 percent ; In recent years, the annual consumption of PP nucleating transparent agent in Japan is about 2000t. If the addition amount is 0.25 percent , the annual output of transparent PP material in Japan can reach more than 800,000t. According to the introduction of Japan Physical and Chemical Co., Ltd., Japan's transparent PP special materials are used in microwave cookers and furniture with the largest consumption. It is estimated that the demand for transparent PP special materials in foreign markets in 2005 is about 5 million to 5.5 million tons. At present, there is a big gap between domestic transparent PP special materials and foreign countries, and the production and application of transparent PP resin and its products still need to be strengthened.

Polyetylen PVC Polystyren Polypropylen Hva er forskjellen Polyetylen PE

Når den er upigmentert, er den melkehvit, gjennomskinnelig og voksaktig; produktet føles glatt når det berøres for hånd, fleksibelt og fleksibelt; den kan strekke seg litt. Vanligvis er polyetylen med lav-tetthet mykere og har bedre gjennomsiktighet. høy-polyetylen er hardere.

Vanlige produkter: håndvesker, vannrør, oljefat, drikkeflasker (kalsiummelkflasker), daglige nødvendigheter, etc.

Polypropylen PP

Hvit gjennomskinnelig, voksaktig når upigmentert; lettere enn polyetylen. Gjennomsiktigheten er også bedre enn polyetylen, og den er hardere enn polyetylen.

Vanlige produkter: servanter, fat, møbler, filmer, vevde poser, flaskekorker, bilstøtfangere, etc.

polystyren PS

Gjennomsiktig når upigmentert. Når produktet slippes eller bankes, har det en metall-som skarp lyd, god glans og gjennomsiktighet, som ligner på glass, sprø og lett å knuse, og overflaten på produktet kan ripes opp med negler. Modifisert polystyren er ugjennomsiktig.

Vanlige produkter: skrivesaker, kopper, matbeholdere, skjell til husholdningsapparater, elektrisk tilbehør, etc.

Polyvinylklorid PVC

Den naturlige fargen er lys gul, gjennomskinnelig og skinnende. Gjennomsiktigheten er bedre enn for polyetylen og polystyren, men dårligere enn for polystyren. Avhengig av doseringen av tilsetningsstoffer, kan den deles inn i myk og hard polyvinylklorid. Myke produkter er fleksible og fleksible, og føles klissete. Hardheten til harde produkter er høyere enn for polyetylen med lav-densitet. , mens lavere enn polypropylen, skjer bleking ved bøyningspunktet.

Vanlige produkter: plater, rør, såler, leker, dører og vinduer, ledningshylster, skrivesaker, etc.

polyetylentereftalat PET

Gjennomsiktigheten er veldig god, styrken og seigheten er bedre enn for polystyren og polyvinylklorid, og den er ikke lett å bryte.

Vanlige produkter: ofte flaskeprodukter som cola, mineralvannflasker, etc.


Sende bookingforespørsel